Your Plumbing Crash Course: A Necessity for Bathtub Installation
View WebsiteJust how do you actually feel when it comes to How to Install a Bathtub Yourself?
Setting up a tub isn't precisely brain surgery, but it does call for strong plumbing, woodworking, and also sometimes, tiling abilities. Changing an old bathtub with a brand-new one is additionally a reasonably challenging job. If the old bathtub is readily accessible, the task can move immediately; if you have to open up a wall to get rid of the old bathtub and position the new tub, the task is a lot harder. In either instance, the job is within a house handyman's skills, although you will certainly need an assistant to leave the old bathtub and set in the brand-new one. Ensure you have qualified yourself for the task as well as are comfortable trying it. As opposed to working with a contractor to take control of a halfway-completed task, it is much better to take into consideration utilizing one prior to you begin. Chances are you may require an expert plumber to make tube links.
This short article will certainly assist you set up a brand-new bath tub in your washroom if you have currently gotten a new bathtub and also do not need to alter the arrangement of your previous supply of water pipes.
Your tools and also product checklist need to comprise the following:
Removing Old Touches
If you need to change old taps with new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, switch on the faucets to drain any water staying in the system. The procedure of eliminating the existing taps can be fairly bothersome because of the restricted gain access to that is often the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a fabric ready for the staying water that will certainly originate from the pipelines. As soon as the supply pipes have been removed, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning during this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any old securing compound.
Prior to moving on to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin guaranteeing that the washing machines are in place in between the faucet and also the sink. Secure the faucet in place with the maker offered backnut. As soon as the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet adapters. The former kind needs to be attached to the faucet ends initially, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bathtub
Using both wooden boards under its feet, put the bath tub in the required setting. The wood boards are valuable in uniformly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto four small factors.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level and readjusting the feet on the bathtub until the spirit level reads degree.
To set up faucets, fit all-time low of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression join; then do the exact same for the other faucet.
Turn on the water system and examine all joints and also brand-new pipework for leakages and also tighten them if needed. Fill up the tub and likewise check the overflow electrical outlet as well as the normal electrical outlet for leakages.
Finally, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the tub ought to wait until the tub has been made use of at the very least once as this will certainly settle it into its last position.
Preparing for the Installation
To start with, the sustaining structure supplied with the bathroom should be fitted (if required) according to the producer's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is essential to ensure that if the faucet includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the tub.
Fit the flexible faucet connectors to the bottom of the two faucets using 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you utilize every one of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its final position.
Tiling Around the Bath tub
In the area where the bath meets the tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to split an inflexible seal, causing the water to pass through the wall surface between the bath as well as the tiling, leading to problems with dampness and possible leaks to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures and fittings. They are offered in tubes and also cartridges, and also can securing spaces up to a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked newspaper or soft rope. Remember to always fill up the bathtub with water prior to securing, to allow for the motion experienced when the tub remains in usage. The sealer can break rather early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally quickly available on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very curious about How to Install a Bathtub Yourself and I'm hoping you enjoyed reading the new article. Do you know about another individual who is serious about How to Install a Bathtub? Please feel free to share it. Thanks a bunch for your time. Visit us again soon.
Set Up An Appointment